At a glance
- Questions in this section of the pool: 44
- Questions from this section on your exam: 4 of 35, one from each group
- Free on this page: group T7A, 11 questions with answers
- Pool in use: 2026 to 2030 (exams given July 1, 2026 through June 30, 2030)
Subelement T7 of the Technician exam covers real equipment and troubleshooting: receivers, transmitters, test gear, soldering, and common station problems. The questions below are from the official question pool, and the questions on your exam will be worded exactly as they are here. The order of the four choices can change, so learn the answer itself and not its letter.
What this section covers
- T7A: Station equipment: receivers, transceivers, transmitter amplifiers, RF preamplifiers, transverters; Basic radio circuit concepts and terminology: sensitivity, selectivity, mixers, oscillators, Push-To-Talk (PTT), VFO, modulation (11 questions, free below)
- T7B: Symptoms, causes, and cures of common transmitter and receiver problems: overload and overdrive, distortion, interference and consumer electronics, RF feedback (11 questions, full binder)
- T7C: Antenna and transmission line measurements and troubleshooting: measuring SWR, effects of high SWR, causes of feed line failures; Basic coaxial cable characteristics; Use of dummy loads when testing (11 questions, full binder)
- T7D: Using basic test instruments: voltmeter, ammeter, and ohmmeter; Soldering (11 questions, full binder)
Free sample: group T7A
Station equipment: receivers, transceivers, transmitter amplifiers, RF preamplifiers, transverters; Basic radio circuit concepts and terminology: sensitivity, selectivity, mixers, oscillators, Push-To-Talk (PTT), VFO, modulation. One question on your exam comes from this group. The correct answer is highlighted.
T7A01
Which term describes the ability of a receiver to detect the presence of a signal?
- RF gain
- Sensitivity
- Selectivity
- Total Harmonic Distortion
Correct answer: B. Sensitivity
Why: Sensitivity is how well a receiver can pick up a weak signal.
T7A02
What is a transceiver?
- A device that combines a receiver and transmitter
- A device for matching feed line impedance to 50 ohms
- A device for automatically sending and decoding Morse code
- A device for converting receiver and transmitter frequencies to another band
Correct answer: A. A device that combines a receiver and transmitter
Why: A transceiver is a transmitter and a receiver in one unit.
T7A03
Which of the following is used to convert a signal from one frequency to another?
- Phase splitter
- Mixer
- Inverter
- Amplifier
Correct answer: B. Mixer
Why: A mixer combines two signals to shift a signal from one frequency to another.
T7A04
Which term describes the ability of a receiver to discriminate between multiple signals?
- Discrimination ratio
- Sensitivity
- Selectivity
- Harmonic distortion
Correct answer: C. Selectivity
Why: Selectivity is how well a receiver separates the signal you want from others close to it in frequency.
T7A05
What is the name of a circuit that generates a signal at a specific frequency?
- Reactance modulator
- Phase modulator
- Low-pass filter
- Oscillator
Correct answer: D. Oscillator
Why: An oscillator generates a signal at a set frequency.
T7A06
What device converts the RF input and output of a transceiver to another band?
- High-pass filter
- Low-pass filter
- Transverter
- Phase converter
Correct answer: C. Transverter
Why: A transverter shifts a transceiver’s signals to another band, for example letting an HF radio operate on a VHF band.
T7A07
What is the function of a transceiver’s PTT input?
- Input for a key used to send CW
- Switches transceiver from receive to transmit when grounded
- Provides a transmit tuning tone when grounded
- Input for a preamplifier tuning tone
Correct answer: B. Switches transceiver from receive to transmit when grounded
Why: PTT stands for push to talk. Grounding the PTT line switches the radio from receive to transmit.
T7A08
Which of the following describes combining speech with an RF carrier signal?
- Impedance matching
- Oscillation
- Modulation
- Low-pass filtering
Correct answer: C. Modulation
Why: Modulation is the process of putting information, such as your voice, onto a radio frequency carrier.
T7A09
What is the function of the switch which selects either SSB or CW-FM on some VHF power amplifiers?
- Change the mode of the transmitted signal
- Set the amplifier for proper operation in the selected mode
- Change the frequency range of the amplifier to operate in the proper segment of the band
- Reduce the received signal noise
Correct answer: B. Set the amplifier for proper operation in the selected mode
Why: The switch sets the amplifier up to work correctly for the mode you are using. Single sideband needs the amplifier to run in a linear way; FM and CW do not.
T7A10
What can be added to the output of a transceiver to increase the transmitted output power?
- A potentiometer
- An RF power amplifier
- An impedance multiplier
- All these choices are correct
Correct answer: B. An RF power amplifier
Why: An RF power amplifier increases the power of the signal coming out of the transceiver.
T7A11
What is the function of the Variable Frequency Oscillator (VFO) circuit in a transceiver?
- Set the receive and transmit frequency
- Provide automatic frequency control
- Inject a variable frequency to allow CW reception
- Generate and demodulate single sideband signals
Correct answer: A. Set the receive and transmit frequency
Why: The VFO, or variable frequency oscillator, is the tuning control. It sets the frequency you receive and transmit on.
The other 3 groups in this section
These 33 questions are worth 3 of the 4 points this section carries on your exam.
T7B
Symptoms, causes, and cures of common transmitter and receiver problems: overload and overdrive, distortion, interference and consumer electronics, RF feedback
11 questions, in the full binder
T7C
Antenna and transmission line measurements and troubleshooting: measuring SWR, effects of high SWR, causes of feed line failures; Basic coaxial cable characteristics; Use of dummy loads when testing
11 questions, in the full binder
T7D
Using basic test instruments: voltmeter, ammeter, and ohmmeter; Soldering
11 questions, in the full binder
The full Technician binder
Get the other 33 questions in T7, with explanations
- All 409 official questions, every group in every section
- A plain-English explanation under each answer
- Unlimited full-length 35-question practice tests
- A printable binder you can study from offline
Keep going
See the Technician exam study guide for how the exam is scored, or try the free 10-question sample test.
Source: NCVEC Question Pool Committee, 2026 to 2030 Technician Class (Element 2) question pool, public release of February 19, 2026. Test Day Binder is not affiliated with the FCC, the NCVEC, or any volunteer examiner group.
Last checked: November 2026.