At a glance
- Questions in this section of the pool: 23
- Questions from this section on your exam: 2 of 35, one from each group
- Free on this page: group T4A, 12 questions with answers
- Pool in use: 2026 to 2030 (exams given July 1, 2026 through June 30, 2030)
Subelement T4 of the Technician exam covers setting up and running a station: connecting equipment, power and grounding, and the common controls on a transceiver. The questions below are from the official question pool, and the questions on your exam will be worded exactly as they are here. The order of the four choices can change, so learn the answer itself and not its letter.
What this section covers
- T4A: Station setup: connecting a microphone, RF power meter, a power source, a computer, digital equipment, an SWR meter; RF grounding; Mobile radio installation (12 questions, free below)
- T4B: Operating controls: frequency tuning, use of filters, squelch function, AGC, memory channels, noise blanker, microphone gain, receiver incremental tuning (RIT), bandwidth selection, scanning function; Digital transceiver configuration; DMR code plugs and talk groups (11 questions, full binder)
Free sample: group T4A
Station setup: connecting a microphone, RF power meter, a power source, a computer, digital equipment, an SWR meter; RF grounding; Mobile radio installation. One question on your exam comes from this group. The correct answer is highlighted.
T4A01
Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver?
- 24.0 volts at 4 amperes
- 13.8 volts at 4 amperes
- 24.0 volts at 12 amperes
- 13.8 volts at 12 amperes
Correct answer: D. 13.8 volts at 12 amperes
Why: A mobile radio runs from about 13.8 volts, the voltage of a running vehicle. A 50-watt radio draws roughly 10 amperes on transmit, so a 12-ampere supply is appropriate.
T4A02
Which of the following should be considered when selecting an accessory SWR meter?
- The frequency and power level at which the measurements will be made
- The distance that the meter will be located from the antenna
- The maximum SWR anticipated on the transmission line
- The ability of the meter to compensate for a poor transmission line match to the antenna
Correct answer: A. The frequency and power level at which the measurements will be made
Why: An SWR meter is built for a certain frequency range and power level. Pick one that covers the frequencies and power you will measure.
T4A03
Why are short, heavy-gauge wires used for a transceiver’s DC power connection?
- To minimize voltage drop when transmitting
- To provide a close match to the power supply output impedance
- To avoid RF interference
- To minimize radiative losses in the power cable
Correct answer: A. To minimize voltage drop when transmitting
Why: A radio draws heavy current when it transmits. Short, thick wires keep the voltage from sagging under that load.
T4A04
How are the audio input and output of a transceiver connected in a station configured to operate using FT8?
- To a computer running a terminal program and connected to a terminal node controller unit
- To the audio output and input of a computer running FT8 software
- To an FT8 conversion unit, a keyboard, and a computer monitor
- To a computer connected to the FT8converter.com website
Correct answer: B. To the audio output and input of a computer running FT8 software
Why: For FT8 the radio’s audio is connected to a computer running the FT8 software: receive audio goes into the computer, and the computer’s audio output goes into the radio.
T4A05
Where should an RF power meter be installed?
- In the feed line, between the transmitter and antenna
- At the power supply output
- In parallel with the push-to-talk line and the antenna
- In the power supply cable, as close as possible to the radio
Correct answer: A. In the feed line, between the transmitter and antenna
Why: A power meter measures what is traveling to the antenna, so it goes in the feed line between the transmitter and the antenna.
T4A06
What signals are used in a computer-radio interface for digital mode operation?
- Receive and transmit mode, status, and location
- Antenna and RF power
- Receive audio, transmit audio, and transmitter keying
- NMEA GPS location and DC power
Correct answer: C. Receive audio, transmit audio, and transmitter keying
Why: A digital-mode interface carries three things: receive audio, transmit audio, and the keying signal that switches the transmitter on.
T4A07
Which of the following is one of the connections required between a computer and a transceiver to operate digital modes?
- Computer “line out” to transceiver push-to-talk
- Computer “line in” to transceiver push-to-talk
- Computer “line in” to transceiver speaker connector
- Computer “line out” to transceiver speaker connector
Correct answer: C. Computer “line in” to transceiver speaker connector
Why: The computer listens to the radio through its line in, so line in connects to the radio’s speaker or audio output. The computer’s line out goes to the radio’s microphone or audio input.
T4A08
Which of the following conductors is preferred for bonding at RF?
- Copper braid removed from coaxial cable
- Copper-clad steel wire
- Twisted-pair cable
- Flat copper strap
Correct answer: D. Flat copper strap
Why: Flat copper strap is preferred for bonding at radio frequencies because its wide surface gives a low-impedance path.
T4A09
How can you determine the length of time that equipment can be powered from a battery?
- Divide the watt-hour rating of the battery by the peak power consumption of the equipment
- Divide the battery ampere-hour rating by the average current draw of the equipment
- Multiply the watts per hour consumed by the equipment by the battery power rating
- Multiply the square of the current rating of the battery by the input resistance of the equipment
Correct answer: B. Divide the battery ampere-hour rating by the average current draw of the equipment
Why: Divide the battery’s ampere-hour rating by the average current the equipment draws. A 20 ampere-hour battery feeding a 2-ampere load lasts about 10 hours.
T4A10
What function does a digital mode hotspot perform for nearby transceivers?
- Communication with a digital voice or data network
- FT8 digital communications via AFSK using a smartphone connected to the internet
- RTTY encoding and decoding without a computer
- High-speed digital communications for meteor scatter
Correct answer: A. Communication with a digital voice or data network
Why: A hotspot is a small low-power device that connects nearby digital radios to a digital voice or data network over the internet.
T4A11
Where should the negative power return of a mobile transceiver be connected in a vehicle?
- At the 12-volt battery chassis ground
- To the shell of the power connector
- To any metal part of the vehicle
- Through the transceiver’s mounting bracket
Correct answer: A. At the 12-volt battery chassis ground
Why: The negative lead goes to the point where the vehicle battery’s negative is grounded to the chassis, which is the solid return path.
T4A12
What is an electronic keyer?
- A device for switching antennas from transmit to receive
- A device for voice activated switching from receive to transmit
- A device that assists in manual sending of Morse code
- An interlock to prevent unauthorized use of a radio
Correct answer: C. A device that assists in manual sending of Morse code
Why: An electronic keyer forms correctly timed dots and dashes when you press its paddles, which makes sending Morse code by hand easier.
The other 1 group in this section
These 11 questions are worth 1 of the 2 points this section carries on your exam.
T4B
Operating controls: frequency tuning, use of filters, squelch function, AGC, memory channels, noise blanker, microphone gain, receiver incremental tuning (RIT), bandwidth selection, scanning function; Digital transceiver configuration; DMR code plugs and talk groups
11 questions, in the full binder
The full Technician binder
Get the other 11 questions in T4, with explanations
- All 409 official questions, every group in every section
- A plain-English explanation under each answer
- Unlimited full-length 35-question practice tests
- A printable binder you can study from offline
Keep going
See the Technician exam study guide for how the exam is scored, or try the free 10-question sample test.
Source: NCVEC Question Pool Committee, 2026 to 2030 Technician Class (Element 2) question pool, public release of February 19, 2026. Test Day Binder is not affiliated with the FCC, the NCVEC, or any volunteer examiner group.
Last checked: November 2026.