At a glance
- Questions in this section of the pool: 37
- Questions from this section on your exam: 3 of 35, one from each group
- Free on this page: group T2A, 11 questions with answers
- Pool in use: 2026 to 2030 (exams given July 1, 2026 through June 30, 2030)
Subelement T2 of the Technician exam covers how to make a contact: choosing a frequency, calling another station, using repeaters, and operating in an emergency or public service event. The questions below are from the official question pool, and the questions on your exam will be worded exactly as they are here. The order of the four choices can change, so learn the answer itself and not its letter.
What this section covers
- T2A: Station operation: choosing an operating frequency, calling another station, test transmissions; Band plans: calling frequencies, repeater offsets (11 questions, free below)
- T2B: VHF/UHF operating practices: FM repeater, simplex, reverse splits; Access tones: CTCSS, DTMF; DMR operation; Resolving operating problems; Q signals (14 questions, full binder)
- T2C: Public service: emergency operations, applicability of FCC rules, RACES and ARES, net and traffic procedures, operating restrictions during emergencies, use of phonetics in message handling (12 questions, full binder)
Free sample: group T2A
Station operation: choosing an operating frequency, calling another station, test transmissions; Band plans: calling frequencies, repeater offsets. One question on your exam comes from this group. The correct answer is highlighted.
T2A01
What is a common repeater frequency offset in the 2-meter band?
- Plus or minus 5 MHz
- Plus or minus 600 kHz
- Plus or minus 500 kHz
- Plus or minus 1 MHz
Correct answer: B. Plus or minus 600 kHz
Why: On 2 meters, repeaters normally listen and transmit 600 kHz apart. Your radio shifts up or down by that amount when you press the transmit button.
T2A02
What is the national calling frequency for FM simplex operations in the 2-meter band?
- 146.520 MHz
- 145.000 MHz
- 432.100 MHz
- 446.000 MHz
Correct answer: A. 146.520 MHz
Why: 146.520 MHz is the national calling frequency for FM simplex on 2 meters. It is where you call when you want a direct contact without a repeater.
T2A03
What is a common repeater frequency offset in the 70-centimeter band?
- Plus or minus 5 MHz
- Plus or minus 600 kHz
- Plus or minus 500 kHz
- Plus or minus 1 MHz
Correct answer: A. Plus or minus 5 MHz
Why: On the 70-centimeter band the standard repeater offset is 5 MHz, much wider than the 600 kHz used on 2 meters.
T2A04
What is an appropriate way to call another station on a repeater if you know the other station’s call sign?
- Say “break, break,” then the other station’s call sign, followed by your call sign
- Say the station’s call sign, then identify with your call sign
- Say “CQ” three times, then the other station’s call sign, followed by your call sign
- Wait for the station to call CQ, then answer with your call sign
Correct answer: B. Say the station’s call sign, then identify with your call sign
Why: On a repeater you do not call CQ. Say the other station’s call sign, then your own.
T2A05
How should you respond to a station calling CQ?
- Transmit “CQ” followed by the other station’s call sign
- Transmit your call sign followed by the other station’s call sign
- Transmit the other station’s call sign followed by your call sign
- Transmit a signal report followed by your call sign
Correct answer: C. Transmit the other station’s call sign followed by your call sign
Why: Answer a CQ by saying the other station’s call sign first, then yours. The order is always who you are calling, then who you are.
T2A06
What is an effective way to seek a call from any phone station when not using a repeater?
- Sign your call sign once, followed by the words “listening for a call;” if there is no answer, change the frequency and repeat
- Say “QTC,” followed by “this is” and your call sign; if there is no answer, change the frequency and repeat
- Transmit an unmodulated carrier for approximately 10 seconds, followed by “this is” and your call sign, and pause to listen; repeat as necessary
- Repeat “CQ” a few times, followed by “this is,” and your call sign, then pause to listen; repeat as necessary
Correct answer: D. Repeat “CQ” a few times, followed by “this is,” and your call sign, then pause to listen; repeat as necessary
Why: Off the repeater, you look for a contact by calling CQ a few times, giving your call sign, and then listening. Repeat as needed.
T2A07
What does the term “repeater offset” mean?
- The difference between a repeater’s transmit and receive frequencies
- The repeater has a time delay to prevent interference
- The approximately half-second delay to allow for the “squelch tail” to be removed
- The fee charged by the repeater owner or club to provide for maintenance
Correct answer: A. The difference between a repeater’s transmit and receive frequencies
Why: A repeater listens on one frequency and transmits on another. The offset is the difference between the two.
T2A08
What is the meaning of the procedural signal “CQ”?
- A shortened form of the term “Contest QSO”
- “Communication Quality,” used to indicate transmitted audio clarity
- Only the called station should transmit
- Calling any station
Correct answer: D. Calling any station
Why: CQ means calling any station. It is an open invitation for anyone who hears you to answer.
T2A09
Which of the following is a customary way to indicate a station is listening on a repeater and looking for a contact?
- “CQ CQ” followed by the repeater’s call sign
- The station’s call sign followed by the word “listening”
- The repeater’s call sign followed by the station’s call sign
- “QSY” followed by your call sign
Correct answer: B. The station’s call sign followed by the word “listening”
Why: On a repeater, the usual way to say you are available is your call sign followed by the word listening or monitoring.
T2A10
What is a band plan, beyond the privileges established by the FCC?
- A voluntary guideline for using different modes or activities within an amateur band
- A list of operating schedules
- A list of available net frequencies
- A plan devised by a club to indicate frequency band usage
Correct answer: A. A voluntary guideline for using different modes or activities within an amateur band
Why: A band plan is a voluntary agreement among amateurs about where different modes and activities go within a band. It goes beyond what the FCC rules require.
T2A11
What term describes an amateur station that is transmitting and receiving on the same frequency?
- Full duplex
- Diplex
- Simplex
- Multiplex
Correct answer: C. Simplex
Why: Simplex means transmitting and receiving on the same frequency, talking directly to the other station with no repeater in between.
The other 2 groups in this section
These 26 questions are worth 2 of the 3 points this section carries on your exam.
T2B
VHF/UHF operating practices: FM repeater, simplex, reverse splits; Access tones: CTCSS, DTMF; DMR operation; Resolving operating problems; Q signals
14 questions, in the full binder
T2C
Public service: emergency operations, applicability of FCC rules, RACES and ARES, net and traffic procedures, operating restrictions during emergencies, use of phonetics in message handling
12 questions, in the full binder
The full Technician binder
Get the other 26 questions in T2, with explanations
- All 409 official questions, every group in every section
- A plain-English explanation under each answer
- Unlimited full-length 35-question practice tests
- A printable binder you can study from offline
Keep going
See the Technician exam study guide for how the exam is scored, or try the free 10-question sample test.
Source: NCVEC Question Pool Committee, 2026 to 2030 Technician Class (Element 2) question pool, public release of February 19, 2026. Test Day Binder is not affiliated with the FCC, the NCVEC, or any volunteer examiner group.
Last checked: November 2026.