At a glance
- Questions in this section of the pool: 36
- Questions from this section on your exam: 3 of 35, one from each group
- Free on this page: group T0A, 12 questions with answers
- Pool in use: 2026 to 2030 (exams given July 1, 2026 through June 30, 2030)
Subelement T0 of the Technician exam covers staying safe: electrical hazards, tower and antenna safety, and limits on exposure to radio frequency energy. The questions below are from the official question pool, and the questions on your exam will be worded exactly as they are here. The order of the four choices can change, so learn the answer itself and not its letter.
What this section covers
- T0A: Power circuits and hazards: hazardous voltages, fuses and circuit breakers, grounding, electrical code compliance; Lightning protection; Battery safety (12 questions, free below)
- T0B: Antenna safety: tower safety and grounding, installing antennas, antenna supports (11 questions, full binder)
- T0C: RF hazards: radiation exposure, proximity to antennas, recognized safe power levels, radiation types, duty cycle (13 questions, full binder)
Free sample: group T0A
Power circuits and hazards: hazardous voltages, fuses and circuit breakers, grounding, electrical code compliance; Lightning protection; Battery safety. One question on your exam comes from this group. The correct answer is highlighted.
T0A01
Which of the following is a safety hazard of a 12-volt storage battery that lacks internal protection circuitry?
- Touching both terminals with your hands can cause electrical shock
- Shorting the terminals can cause burns, fire, or an explosion
- RF emissions from a nearby transmitter can cause the electrolyte to emit poison gas
- All these choices are correct
Correct answer: B. Shorting the terminals can cause burns, fire, or an explosion
Why: A 12-volt battery can deliver a very large current. Shorting the terminals can cause burns, a fire or an explosion. Twelve volts is too low to shock you through dry skin.
T0A02
What health hazard is posed by electrical current flowing through the body?
- It may cause injury by heating body tissue
- It may disrupt the electrical functions of cells
- It may cause involuntary muscle contractions
- All these choices are correct
Correct answer: D. All these choices are correct
Why: Current through the body can heat tissue, disrupt the electrical signals of cells, and make muscles contract involuntarily.
T0A03
In the United States, what circuit does black wire insulation indicate in a three-wire 120 V AC cable?
- Neutral
- Hot
- Equipment ground
- Negative
Correct answer: B. Hot
Why: In United States household wiring, black is hot, white is neutral, and green or bare copper is ground.
T0A04
What is the purpose of a fuse in an electrical circuit?
- To prevent power supply ripple from damaging a component
- To remove power in case of an overload
- To limit current and prevent shocks
- All these choices are correct
Correct answer: B. To remove power in case of an overload
Why: A fuse cuts off power when too much current flows.
T0A05
Why should a 5-ampere fuse never be replaced with a 20-ampere fuse?
- The larger fuse would be likely to blow because it is rated for higher current
- The power supply ripple would greatly increase
- Excessive current could cause a fire
- Voltage drop in the higher current fuse could result in excessively low voltage to the device
Correct answer: C. Excessive current could cause a fire
Why: A fuse is sized to protect the wiring and the equipment. A larger fuse lets too much current through, and the wiring can overheat and start a fire.
T0A06
What is a good way to guard against electrical shock at your station?
- Use three-wire cords and plugs for all AC powered equipment
- Connect all AC powered station equipment to a common safety ground
- Ensure all capacitors used for high-voltage DC are fully discharged before working inside equipment
- All these choices are correct
Correct answer: D. All these choices are correct
Why: All three protect against shock: three-wire cords, a common safety ground, and discharging high-voltage capacitors before working inside equipment.
T0A07
Where should a lightning arrester be installed in a coaxial feed line?
- At the output connector of a transceiver
- At the antenna feed point
- At the AC power service panel
- On a grounded panel near where feed lines enter the building
Correct answer: D. On a grounded panel near where feed lines enter the building
Why: A lightning arrester belongs on a grounded panel near where the feed lines enter the building, so the surge is sent to ground before it gets inside.
T0A08
Where should a fuse or circuit breaker be installed in a 120V AC power circuit?
- In series with the hot conductor only
- In series with the hot and neutral conductors
- In parallel with the hot conductor only
- In parallel with the hot and neutral conductors
Correct answer: A. In series with the hot conductor only
Why: A fuse or breaker goes in series with the hot wire only, so that when it opens, the circuit is disconnected from the live side.
T0A09
What should be done to all external ground rods or earth connections?
- Waterproof them with silicone caulk or electrical tape
- Keep them as far apart as possible
- Bond them together with heavy wire or conductive strap
- Tune them for resonance on the lowest frequency of operation
Correct answer: C. Bond them together with heavy wire or conductive strap
Why: All ground rods and earth connections should be bonded together with heavy wire or strap, so there is no voltage difference between them during a lightning strike.
T0A10
What hazard exists when rapidly charging or discharging an unprotected battery?
- Overheating or out-gassing
- Excess output ripple
- Electric shock
- Overvoltage
Correct answer: A. Overheating or out-gassing
Why: Charging or discharging a battery too fast can make it overheat or give off gas, which can lead to fire or explosion.
T0A11
What hazard exists in a power supply immediately after turning it off?
- Circulating currents in the dc filter
- Leakage flux in the power transformer
- Voltage transients from kickback diodes
- Charge stored in filter capacitors
Correct answer: D. Charge stored in filter capacitors
Why: The filter capacitors in a power supply can hold a dangerous charge after the supply is switched off.
T0A12
Which of the following precautions should be taken when measuring high voltages with a voltmeter?
- Ensure that the voltmeter has very low impedance
- Ensure that the voltmeter and its leads are rated for use at the voltages being measured
- Ensure that the circuit is grounded through the voltmeter
- Ensure that the voltmeter is set to the correct frequency
Correct answer: B. Ensure that the voltmeter and its leads are rated for use at the voltages being measured
Why: The meter and its test leads must be rated for the voltage you are measuring.
The other 2 groups in this section
These 24 questions are worth 2 of the 3 points this section carries on your exam.
T0B
Antenna safety: tower safety and grounding, installing antennas, antenna supports
11 questions, in the full binder
T0C
RF hazards: radiation exposure, proximity to antennas, recognized safe power levels, radiation types, duty cycle
13 questions, in the full binder
The full Technician binder
Get the other 24 questions in T0, with explanations
- All 409 official questions, every group in every section
- A plain-English explanation under each answer
- Unlimited full-length 35-question practice tests
- A printable binder you can study from offline
Keep going
See the Technician exam study guide for how the exam is scored, or try the free 10-question sample test.
Source: NCVEC Question Pool Committee, 2026 to 2030 Technician Class (Element 2) question pool, public release of February 19, 2026. Test Day Binder is not affiliated with the FCC, the NCVEC, or any volunteer examiner group.
Last checked: November 2026.